RK3588 Custom Kiosk Board, WF-C3588-I1, AndroidSBC, Vienna

TL;DR: RK3588 Custom Kiosk Board

Vienna, Austria - September 12, 2026. The 369th WF-C3588-I1 shipment left Shenzhen for Vienna this week with 17,760 units aboard, after a full burn-in cycle and a destination-market document check.

AndroidSBC export paperwork update on the nine-variant WF-C3588 custom board line serving Vienna, Austria. What Austria importers get from the WF-C3588 programme is a single Rockchip RK3588 silicon across nine custom motherboard variants, all built at the Wanlin Longgang plant in Shenzhen. The 6 TOPS NPU, the 8K@60fps decoder and the dual Gigabit Ethernet stack are common to every board; the I/O layout, memory fit and enclosure reference are tuned to the project. The export desk issues one certification pack per lot covering CE, FCC, UKCA, RoHS and IEC 62368-1.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group, and the WF-C3588 is its nine-variant custom motherboard programme. Custom Android motherboards, custom industrial boards, core board and SOM carrier work, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards all sit on the same Rockchip RK3588 silicon with 6 TOPS NPU. The Longgang plant in Shenzhen runs its own SMT lines, aging racks and EMC pre-compliance bench, so the export file is produced where the boards are built. For Austria importers that removes the usual gap between the factory that makes the custom board and the party that has to answer for it at customs.

WF-C3588-I1 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-I1 (Custom Industrial Motherboard for Fanless and Wide-Temperature Control) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Austria importers sourcing the WF-Series, the 8GB + 32GB (WF-C3588-I1-B) variant is the typical configuration for the custom industrial control and HMI programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Industrial Motherboard for Fanless and Wide-Temperature Control for Austria Buyers

For Austria procurement teams, the first surprise on the custom industrial motherboard for fanless and wide-temperature control line is rarely technical. It is that the sample arrives on time and the production lot does not, because the Rockchip RK3588 allocation cannot be conjured from broker stock when a 17,760-unit order is confirmed. Then comes the firmware question. The hardware spec is straightforward to verify; whether the board holds a credential-locked stack through a 72-hour loop and a field OTA is a different test, and it is normally the Vienna buyer's warehouse that discovers the answer.

Documentation is the third item on the list. A CE mark without a matching Declaration of Conformity and Technical File is not a marking problem, it is a customs problem, and it tends to surface after the goods are already on the water. AndroidSBC's approach is to close the gap at the factory gate. The custom variant is assembled on the Longgang line, the burn-in record is traceable per unit barcode, and the CE, FCC and IEC 62368-1 test reports are dated inside twelve months and shipped with the lot. The nine WF-C3588 variants span industrial HMIs, panel PCs, PLC upgrades, SCADA nodes, DIN-rail controllers, factory automation, data acquisition, IIoT gateways, and machine control, with three memory configurations per variant for Vienna buyers who need a standard custom SKU rather than a from-scratch build.

For Austria specifically, the file travels with the goods. In Austria distribution is concentrated among a small group of technical wholesalers, so a single listing agreement often decides whether a board reaches the wider integrator market. AndroidSBC prepares the CE marking with the Austrian radio interface notification documentation for TKK / RTR, attaches the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), and consigns the lot to Port of Koper, Adriatic gateway on the Koper to Ningbo lane.

Competitive Comparison: WF-C3588-I1 vs Competing RK3588 Boards

The boards competing for the same socket in the custom industrial motherboard for fanless and wide-temperature control segment fall into three groups: off-the-shelf catalogue boards with no customization path, re-badged imports where the seller controls neither PCB nor firmware, and source-factory custom platforms with an engineering desk behind them. The WF-C3588-I1 sits in the third group and adds three things: Rockchip RK3588 silicon, an I/O and thermal profile that survives a continuous decode-and-NPU loop, and the per-lot certified image burn at Longgang.

• vs commercial boards in industrial dress: the WF-C3588-I1 is designed to -40C to 85C from the schematic up, not a consumer board with a bigger heatsink.
• vs local integrator bundles: the carrier design, the BSP port and the DIN-rail chassis all come from one Longgang engineering desk, so responsibility never splits across vendors.
• vs legacy PLC upgrade paths: the 6 TOPS NPU adds on-device vision and predictive maintenance to a PLC retrofit without a separate AI box.
• vs trading-company boards: the per-lot Technical File, the aging record and the EMC pre-compliance bench all live inside the source factory.

Global Custom Industrial Motherboard and Panel PC Market Trends

The Custom Industrial Motherboard and Panel PC market sets the pace for Vienna procurement this year, and it does not move on its own. The Edge AI hardware segment that MarketsandMarkets values at USD 26.9 billion in 2025, with a 32.7 percent CAGR reaching USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), sets the silicon allocation backdrop that custom RK3588 motherboard buyers also compete for. Three patterns stand out in the WF-C3588 order book for Austria:

• Industrial HMI panel: a machine builder replaces an aging Windows panel with a fanless HMI running a Yocto image and a custom UI.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-I1 board carries that headroom without a board change.
• SCADA edge node: a utility deploys DIN-rail controllers that aggregate substation data and push it over dual Gigabit links.

Analysts covering the Custom Industrial Motherboard and Panel PC space point to the same pattern in Austria: order books are being built around platform breadth rather than a single part number.

The common thread in Austria is that single orders are being replaced by blanket agreements with a monthly release, because a custom board programme that has to survive a twelve-month window cannot absorb an allocation gap in the middle of it.

Partner Success Story: Ferrovia Transit Tech in Vienna, Austria

Ferrovia Transit Tech, a rail HMI contractor serving the Austria market, deployed 5,200 custom WF-C3588-I1 industrial boards for platform HMI and gate control. The rollout covered the industrial hmi panel, scada edge node, and factory automation cell workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 5,200 custom WF-C3588-I1 industrial boards for platform HMI and gate control
• Region: Vienna, Austria
• Models used: WF-C3588-I1 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shanghai Yangshan with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Koper, Adriatic gateway via the Koper to Ningbo lane

"Rail cabinets have no air conditioning and no patience. AndroidSBC routed the CAN and multi-serial lines we asked for, ported the Yocto BSP to our carrier, and the wide-temperature variants have now held through two summers."

- James Whitfield, Programme Manager

Field Report: container yard at Yantian, where 17,760 WF-C3588-I1 boards from the Wanlin export base are being loaded onto containerised pallets with the customs declaration naming the Longgang source factory

Reporter Liang Wei, on the ground in Vienna, Austria. The yard crew handled the order on flat pallets wrapped in anti-static film, with every carton barcode-traced back to the burn-in record. The customs broker attached a single declaration naming the Wanlin Longgang source factory as the place of origin, and the container was sealed before the afternoon cut-off.

The line ran the WF-C3588-I1 boards through a 30-minute HDR10 loop at the inspection bench with no colour banding reported by the operator.

The inspection confirmed three things on the spot: the WF-C3588-I1 units hold the burn-in with a yield above 99.51 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE marking with the Austrian radio interface notification administered by TKK / RTR, cleared for entry at Port of Koper, Adriatic gateway on the Koper to Ningbo lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Austria importers can hand straight to their customs broker.

Filed by Liang Wei, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-I1 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-I1 (Custom Industrial Motherboard for Fanless and Wide-Temperature Control) as the lead SKU for Vienna and Austria programmes:

• Industrial HMI panel: a machine builder replaces an aging Windows panel with a fanless HMI running a Yocto image and a custom UI.
• PLC upgrade retrofit: a plant keeps the field wiring and swaps the controller for a CAN-equipped board with Modbus passthrough.
• SCADA edge node: a utility deploys DIN-rail controllers that aggregate substation data and push it over dual Gigabit links.
• Machine vision inspection: the 6 TOPS NPU runs defect classification at line speed on a 3.5-inch SBC inside the cabinet.
• Data acquisition gateway: a multi-serial variant logs sensor traffic from RS485 chains and buffers it during link loss.
• Factory automation cell: a systems integrator drives a robot cell and its safety stack from one wide-temperature board.
• Outdoor kiosk controller: an unattended terminal survives summer heat in a sealed enclosure with no fan to clog.
• Predictive maintenance: vibration and acoustic models run locally on the NPU and alarm before the PLC does.

Partnership Models for Vienna Buyers

The WF-C3588 custom line is available to Austria partners through three routes, and they can be mixed inside one agreement:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from Longgang under one documentation pack covering CE, FCC, UKCA, RoHS and IEC 62368-1. A Vienna first order on the WF-C3588-I1 is normally the 8GB + 32GB (WF-C3588-I1-B) configuration at MOQ 5,000 units per shipment, standard samples in 1-3 days and 15-30 days to production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Everything from the copper up. Custom PCB and PCBA, custom I/O routing, custom memory and storage configuration, custom display and camera interfaces, custom thermal profile from commercial to -40C to 85C industrial, and custom branding including silk-printed logo, packaging, SKU label and boot animation. The firmware side covers custom Android (GMS or AOSP), Ubuntu, Debian, Yocto and OpenHarmony builds with BSP ports handled by the Longgang engineering desk rather than handed to the buyer as an unmodified vendor drop.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes, and that work stays in-house. The ODM tier covers custom Android ROM builds with proprietary services and launchers, AOSP builds without Google services, and Linux images on Ubuntu, Debian, Yocto or Buildroot. BSP ports for custom carrier boards are executed by the Longgang engineering desk, with SDK and BSP source released to the partner under NDA. The same desk handles driver development for the I/O you added, which is the part that usually stalls when a factory forwards a vendor drop and walks away.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: Yes. Custom NPU development covers RKNN model deployment, quantization from the major frameworks, multi-model pipelines on the triple-core NPU, and custom AI algorithm integration. The desk validates throughput on your exact memory configuration, and the deployment lands as a versioned RKNN file that OTA can update in the field, which is how Austria partners iterate models without replacing hardware.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Samples of standard variants leave the factory in 1-3 days. Custom builds run 15-30 days to mass production once the design is signed off, with the schematic review and carrier design handled in the same window. MOQ sits at 5,000 units per shipment on standard configurations, custom runs are quoted against volume, and small pilot batches are accepted for first-article programmes.

What certifications does a custom board need for Austria, and who handles them?

Answer: AndroidSBC handles them at the factory. Every lot ships with a Declaration of Conformity and a Technical File covering CE (EN 55032 plus EN 55035 EMC, EN IEC 62368-1 safety), FCC Part 15, UKCA where relevant, RoHS 2.0 and the REACH declaration, all dated within the prior twelve months. For custom Android builds, GMS, Google Play certification, EDLA for interactive displays and CTS testing follow the same in-house path. Where a Austria market needs an additional national mark, the export desk confirms coverage before the order is confirmed rather than after.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum supply, patches maintained across the firmware lines, OTA for firmware and NPU model updates. For a Austria programme running a custom board in the field, that commitment is written into the agreement at signature, which is what separates a source factory from a catalogue reseller.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: That is routine. AndroidSBC delivers DDP into Amazon FBA in the US, EU and Japan and into 3PL consolidation points at Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton and pallet configuration follows FBA inbound rules, and the place of origin on the declaration is the Wanlin Longgang source factory.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: The DOA target is 0.3 percent over twelve months. For RMA, partners send the WF-C3588-I1 unit back to Longgang with the burn-in barcode attached, and replacements go out within ten business days. The per-unit record means the failure report usually carries a root cause alongside the replacement, which is what a Austria integrator running a custom configuration actually needs.

Contact AndroidSBC: Start Your WF-C3588-I1 Sourcing Conversation

Wanlin Manufacturing Group sells the WF-C3588 custom motherboard line overseas through AndroidSBC. Vienna and Austria importers, brand owners and channel distributors who want to source the custom industrial motherboard for fanless and wide-temperature control direct from the Longgang plant can reach the export desk through:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE marking with the Austrian radio interface notification for Austria, administered by TKK / RTR, entering at Port of Koper, Adriatic gateway on the Koper to Ningbo lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

To speed up a custom board review, include the target volume, the I/O and firmware changes you need, and your preferred Incoterm. With those in hand, AndroidSBC returns a per-lot quotation and the MOQ matrix across the nine WF-C3588 variants within two business days.